产品介紹   

首页 > 产品中心 > 减速机

PH系列行星减速机

产品特点:

概要


输出额定力矩

T2N : 14 Nm - 2000 Nm


減速比:

单节 :3 / 4 / 5 / 8

双节 :12 / 16 / 20 / 25 / 32 / 40 / 64

参节 : 80 / 100 / 125 / 160 / 200 / 256 / 320 /512


低背隙

单节 : ≤10arcmin

双节 : ≤18arcmin

叁节 : ≤22arcmin

: ≧ 97%

双节 : ≧ 94%

参节 : ≧ 92%

容易安裝

低噪音

结构紧凑


型号

PH240 / PH285 /PH330 / PH400 


减速机性能资料


減速機性能資料

減速機性能資料


开机前的注意事项

Matters that need attention before shutting down

出厂时已按规定量加入洞滑油,因此到货后可直接使用。

首次运转时,请先确认输出轴的转向,然后逐渐增加负荷。

Thespeifed amount of Lincant has been added before deivery so the machine can be used diredty when arived.

Confim the olling direction of the output shaft and increase the load gradually the frst tme operating.


每日检查

Daily check

运转中减速机外壳温度有无异常上升?(最高不大于90C)

轴承、齿轮等部位有无异响?

减速机有无异常振动?1出现此类异常时,请立即停机并联系我公司。)

有无润滑油漏油?(出现油脂泄漏时,请联系我公司。)

Whether the temperature of the reducer shell eises

abnomally?0Maxmum 90 degreel

Are there any abnomal condtions on adetrees or chain wheels? is the reducer vibrating abnommally? 0f i happens, please shut down the

machine and contact our company)

is the lubicant eaking? (Hf it happens, please contact our company)


运转中的注意事项

Matters that need attention during operating

请注意不得过载。

输出轴的转速不得大于规定转速。

出现以下情况时,请停机检查。

1、温度突然开始升高

2、突然发出很大异响。

3、转速突然开始不稳定。

可能的原因如下,请及时处理。

1、是否处于过载状态?

2、轴承、齿轮、传动面有无损伤?

3、机器连接条件有无异常?

Do not overboaded.

The rlling speed of the output shaft should not be faster than the

spedfied one.

Please shut the machine down when folowing situaton shows.

1、The temperature rise suddenly.

2、Strange noise are emerged.

3、The oing speed becomes unstable.

The possible reasons are as fllows., and please make sure to deal with

it in time.

1、Whether it is overloaded or not?

2. Ave the axletrees, gear wheels and the oling side damaged?

3、Is the connecting condition aboomal?


定期检查

Regular check


有无过载状态,有无异常旋转?

皮带轮、链轮、减速机安装螺栓等有无松动?

主要部件的检查与维护。(出现异常现象时,请立即停机并联系我公司。)

Whether it is overloaded or rling abnomaly?

Is the belt pulley. chain wheel. the Insalltion bot of the reducer loose?

The check and mainterance of main components. (When there is an abnomal phenomenon, please shut down the machine. and contact our cormpeany,) .


润滑油管理

The lubricant managing

油脂不能更换。

The grease can not be replaced.